- 地址：
- 安國市南陽工業區
- 郵箱：
- 415130881@qq.com
- 電話：
- 18631165157
- 傳真：
- 0312-3427286
- 手機：
- 18631165157
渣漿泵水力損失與水力效率
水力損失發生在泵的吸水室、葉輪流道、壓水室中。水力損失可分為三種情況:①液體流經泵的吸水室、葉輪流道、壓水室時與壁面發生的沿程摩擦損失;②發生在上述流道的突然擴大、縮小、轉彎等的局部阻力損失;③當運行工況發生改變時發生在葉片進口及出口的撞擊損失。
沿程摩擦阻力損失及局部阻力損失可按水力學中的計算方法來進行計算。但是迄今為止還無法精確的計算，通過上述分析可以看出降低流道表面粗糙度，清理打磨流道，流道面積變化均勻，避免過大的擴散等，可以減小水力損失。葉片進口的沖擊損失，在設計流量下，液流角與葉片安放角是一致的，撞擊損失較小。但當泵不在設計流量工作時，液流角與葉片安放角不再一致，撞擊損失較大，如圖2-38所示。葉輪出口的水力損失，當泵在設計流量工作時，葉輪出口處的流速與壓水室中液體流速基本相等，不會產生很大的損失，而當偏離設計流量工作時，兩者的流速不再相等，從而產生較大的損失。所以選用泵時，應盡量在設計工況下(即高效區)工作，否則會增加泵的水力沖擊損失。
水力效率:
ηh=H/H+△H=H/HT
式中 H----泵的有效揚程;
Ht----泵的理論揚程。
四、泵的效率η
泵的總效率η即為泵的機械效率、容積效率和水力效率的乘積。渣漿泵廠家
Hydraulic loss and efficiency of slurry pump
The hydraulic loss occurs in the suction chamber, impeller passage and pressure chamber of the pump. The hydraulic loss can be divided into three situations: ① the friction loss along the wall when the liquid flows through the suction chamber, impeller passage and pressure chamber of the pump; ② the local resistance loss when the passage expands, shrinks and turns suddenly; ③ the impact loss at the inlet and outlet of the blade when the operation conditions change.
Friction loss along the way and local resistance loss can be calculated according to the calculation method in hydraulics. However, up to now, it has not been able to calculate accurately. Through the above analysis, it can be seen that reducing the surface roughness of the runner, cleaning and polishing the runner, uniform change of the runner area, avoiding excessive diffusion, etc., can reduce the hydraulic loss. Under the design flow rate, the angle of liquid flow is the same as the angle of blade setting, and the impact loss is smaller. However, when the pump is not working at the design flow, the liquid flow angle is no longer consistent with the blade setting angle, and the impact loss is large, as shown in figure 2-38. When the pump is working at the design flow, the flow velocity at the outlet of the impeller is basically the same as that of the liquid in the water pressure chamber, which will not cause great loss. When the pump is working at the design flow, the flow velocity of the two is no longer equal, which will cause great loss. Therefore, when selecting the pump, we should try to work in the design condition (i.e. high efficiency area), otherwise, it will increase the hydraulic impact loss of the pump.
Hydraulic efficiency:
ηh=H/H+△H=H/HT
Where h is the effective head of the pump;
HT ---- theoretical head of pump.
IV. pump efficiency η
The total efficiency η of the pump is the product of the mechanical efficiency, volumetric efficiency and hydraulic efficiency of the pump. Slurry pump manufacturer
上一條：容積損失與渣漿泵容積效率比例
下一條：渣漿泵機械密封的維護
